E39-R1 datasheet(93/100 Pages) OMRON

93 / 100 page

Safety Precautions

Threaded

Cylindrical

Flat

Sleeved

Small Spot

High Power

Retro-

reflective

Limited-

reflective

Narrow

view

BGS

Chemical-

resistant,

Oil-resistant

Bending

Heat-

resistant

Area

Detection

Liquid-level

Vacuum

FPD,

Semi,

Solar

Installation

Information

Installation

Information

Threaded

Cylindrical

Flat

Sleeved

Small Spot

High Power

Retro-

reflective

Limited-

reflective

Narrow

view

BGS

Chemical-

resistant,

Oil-resistant

Bending

Heat-

resistant

Area

Detection

Liquid-level

Vacuum

FPD,

Semi,

Solar

Fiber Unit Connection Side Hook

DIN Track

Tighten the screw while pressing the

End Plate.

Protective

Cover

Fiber Unit

Single Core

Multi Core

Lock Lever

Lock

Release

Protective Sticker

Power Supply

Connecting Terminal

Protective Cap

Precautions for Safe Use

Fiber Amplifier Unit

For common precautions, refer to www.ia.omron.com

Mounting the Fiber Amplifier Units

Mounting Fiber Units

This product is not designed or rated for

ensuring safety of persons either directly

or indirectly.

Do not use it for such purposes.

The following precautions must be observed to ensure safe

operation of the product. Doing so may cause damage or fire.

Precautions for Correct Use

(1) Be sure to mount the unit to the DIN track until it clicks.

(2) When using Amplifier Units with Wire-saving Connectors, attach

the protective stickers (provided with E3X-CN-series

Connectors) on the unused power pins to prevent electrical

shock and short circuiting. When using Amplifier Units with

Connectors for Communications Units, attach the protective

caps (provided with Sensor Communications Unit).

Mounting Amplifier Units in Group

(Wire-saving Connector Type Models)

1. Mount the Fiber Amplifier units

one at a time onto the DIN track

and push them until they click.

2. Slide the Fiber Amplifier units in

the direction 2.

3. Use End Plates (PFP-M: separately

sold) at the both ends of the

grouped Fiber Amplifier units to

prevent them from separating due

to vibration or other cause.

4. Tighten the screw on the End

Plates using a driver.

(3) <E3NX-FA series>

The length for the cable extension must be 30 m or less (or

less than 10 m for S-mark certified models).

Be sure to use a cable of at least 0.3 mm2 for extension.

The power voltage must be 24 to 30 V when connecting

amplifier units with extension cable and wire-saving connector.

<E3X-HD series>

The length for the cable extension must be 100 m or less.

Be sure to use a cable of at least 0.3 mm2 for extension.

(4) Do not apply the forces on the cord exceeding the following

limits: Pull: 40N; torque: 0.1N·m; pressure: 20N; bending:

29.4N

(5) Do not apply excessive force such as tension, compression or

torsion to the Amplifier Unit with the Fiber Unit fixed to the

Amplifier Unit.

(6) Always keep the protective cover in place when using the

Amplifier Unit. Not doing so may cause malfunction.

(7) It may take time until the received light intensity and

measured value become stable immediately after the power

is turned on depending on use environment.

(8) The product is ready to operate 200 ms after the power supply

is turned ON.

(9) The Mobile Console E3X-MC11, E3X-MC11-SV2 and

E3X-MC11-S cannot be connected.

(10) Mutual interference prevention on the E3NX-FA Series does

not function among the E3X-HD, E3X-DA-S, E3X-DA-N,

E3X-SD, or E3X-NA Fiber Amplifier Units.

Mutual interference prevention on the E3X-HD Series does

not function among the E3NX-FA, E3X-DA-N, E3X-SD, or

E3X-NA Fiber Amplifier Units.

Mutual interference prevention on the E3X-HD Series does

function among the E3X-DA-S and E3X-MDA Fiber Amplifier

Units.

(11) If the unit receives excessive sensor light, the mutual

interference prevention function may not work properly,

resulting in malfunction of the unit. In such case, increase the

threshold.

(12) The E3NW-ECT Sensor Communications Unit can be used

with the E3NX-FA0, but the E3X-DRT21-S, E3X-CRT, and

E3X-ECT Sensor Communications Units cannot be used.

The E3X-CRT and E3X-ECT Sensor Communications Unit

can be used with the E3X-HD0, but the E3X-DRT21-S and

E3NW-ECT Sensor Communications Units cannot be used.

(13) If you notice an abnormal condition such as a strange odor,

extreme heating of the unit, or smoke immediately stop using

the product, turn off the power, and consult your dealer.

(14) Do not use thinner, benzine, acetone, and lamp oil for cleaning.

Do not use the product with voltage in

excess of the rated voltage.

Excess voltage may result in malfunction

or fire.

Never use the product with AC power supply.

Otherwise, explosion may result.

• Under environments such as vibration, use an end plates

even with a single Fiber Amplifier Unit.

• The maximum numbers of connectable Amplifier Units are

given in the following table.

• If Units are to be connected, the ambient temperature will change

with the number of Units that are connected. Check the Ratings

and Characteristics specifications.

• Always turn OFF the power before connecting or disconnecting

Units.

* The mutual interference prevention function cannot be used

if the detection mode is set to super-high-speed mode (SHS).

1. Open the protective cover.

2. Raise the lock lever.

3. Insert the Fiber Unit in the

fiber unit hole to the bottom.

4. Return the lock lever to the

original position and fix the

Fiber Unit.

• When mounting a coaxial

reflective Fiber Unit, insert

the single-core Fiber Unit

to the upper hole (Emitter

side) and the multi-core

Fiber Unit to the lower hole (Receiver side).

The cables for the Single-core Fiber Units (Emitters) have

identification marks. Refer to the dimensions diagrams for

details.

• When removing the Fiber Unit, follow the above steps in reverse

order.

To maintain the characteristics of the Fiber Unit, make sure the

lock is released before removing the Fiber Unit.

Maximum

number of mutual

interference

prevention

Maximum

number of

interconnected

E3X-HD series standard models*

(E3X-HD11/HD41/HD6/HD8)

E3X-HD0

With E3X-ECT

With E3X-CRT

Thin Fiber Attachment

(E39-F9)

Loosely tighten.

Fiber Cutter

E39-F4

Thin-diameter

Fiber Unit Hole × 2

Standard Fiber

Unit Hole

(dia. 2.2 mm) × 3

About 0.5 mm

Insertion direction

Cut a thin fiber as follows.

For standard fibers, insert to the desired cutting position and cut.

Adjust the fiber

to the desired

length and fully

tighten.

(1)

(2)

Insert the Fiber

Unit into E39-F4

and cut it.

(3)

Finished state.

(Correctly cut end)

(4)

Amplifier Unit with

Wire-saving Connector

Amplifier Unit with Connector

for Communications Unit

E3NX-FA series*

Warning

(1) Do not install the product in the following locations.

• Locations subject to direct sunlight

• Locations subject to condensation due to high humidity

• Locations subject to corrosive gas

• Locations subject to vibration or mechanical shocks exceeding

the rated values

• Locations subject to exposure to water, oil, chemicals

• Locations subject to stream

• Locations subjected to strong magnetic field or electric field

(2) Do not use the product in environments subject to flammable

or explosive gases.

(3) Do not use the product in any atmosphere or environment

that exceeds the ratings.

(4) To secure the safety of operation and maintenance, do not

install the product close to high-voltage devices and power

devices.

(5) High-Voltage lines and power lines must be wired separately

from this product. Wiring them together or placing them in

the same duct may cause induction, resulting in malfunction

or damage.

(6) Do not apply load exceeding the ratings. Otherwise, damage

or fire may result.

(7) Do not short the load. Otherwise, damage or fire may result.

(8) Connect the load correctly.

(9) Do not miswire such as the polarity of the power supply.

(10) Do not use the product if the case is damaged.

(11) Burn injury may occur. The product surface temperature

rises depending on application conditions, such as the

ambient temperature and the power supply voltage. Attention

must be paid during operation or cleaning.

(12) When setting the Sensor, be sure to check safety, such as by

stopping the equipment.

(13) Be sure to turn off the power supply before connecting or

disconnecting wires.

(14) Do not attempt to disassemble, repair, or modify the product

Unit in any way.

(15) When disposing of the product, treat it as industrial waste.

(16) Do not use the Sensor in water, rain, or outdoors.

1. Let the hook on the Amplifier

Unit's Fiber Unit connection side

catch the track and push the unit

until it clicks.

Mounting on DIN Track

1. Push the unit in the direction 1.

2. Lift it up in the direction 2.

Removing from DIN Track

Refer to “I/O Circuit Diagrams” or

check the side of the unit for wire color

and role indications.

Mount Fiber Unit

Use Fiber Cutter

The fiber is

shipped loosely

tightened as

shown in the

figure at the

right

Note:

The insertion direction into the Fiber

Amplifier Unit is shown in the above figure.

25 mm 10 mm

11.7 mm

E39-R1 Datenblatt(PDF) 93 Page - Omron Electronics LLC

E39-R1 Datenblatt(HTML) 93 Page - Omron Electronics LLC

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100

Datenblatt Download

Link URL