LT1952IGN datasheet(15/24 Pages) LINER

15 / 24 page

LT1952/LT1952-1

19521fd

Programming Synchronous Rectiﬁer Timing:

SOUT to OUT delay (‘tDELAY’)

The LT1952/LT1952-1 have an additional output SOUT

which provides a

±50mA peak drive clamped to 12V. In

applications requiring synchronous rectiﬁcation for high

efﬁciency, the LT1952/LT1952-1 SOUT provides a sync

signal for secondary side control of the synchronous

rectiﬁer MOSFETs (Figure 11). Timing delays through the

converter can cause non-optimum control timing for the

synchronous rectiﬁer MOSFETs. The LT1952/LT1952-1

provide a programmable delay (tDELAY, Figure 8) between

SOUT rising edge and OUT rising edge to optimize timing

control for the synchronous rectiﬁer MOSFETs to achieve

maximum efﬁciency gains. A resistor RDELAY connected

from the DELAY pin to ground sets the value of tDELAY.

Typical values for tDELAY range from 10ns with RDELAY =

10k to 160ns with RDELAY = 160k. (see graph in Typical

Performance Characteristics)

APPLICATIONS INFORMATION

SS_MAXDC pin using a resistor divider from VREF. An

increase of voltage at the SS_MAXDC pin causes the

maximum duty cycle clamp to increase.

To program the volt-second clamp, the following steps

should be taken:

(1)The maximum operational duty cycle of the converter

should be calculated for the given application.

(2)An initial value for the maximum duty cycle clamp

should be calculated using the equation below with a

ﬁrst pass guess for SS_MAXDC.

Note: Since maximum operational duty cycle occurs at

minimum system input voltage (UVLO), the voltage at the

SD_VSEC pin = 1.32V.

Max Duty Cycle Clamp (OUT pin)

= k • 0.522(SS_MAXDC(DC)/SD_VSEC) –

(tDELAY • fOSC)

where,

SS_MAXDC(DC) = VREF(RB/(RT + RB)

SD_VSEC = 1.32V at minimum system input voltage

tDELAY = programmed delay between SOUT and OUT

k = 1.11 – 5.5e–7 • (fOSC)

(3) The maximum duty cycle clamp calculated in (2) should

be programmed to be 10% greater than the maximum

operational duty cycle calculated in (1). Simple adjust-

ment of maximum duty cycle can be achieved by adjusting

SS_MAXDC.

Figure 8. Programming SOUT to OUT Delay: tDELAY

1952 F08

DELAY

LT1952/

LT1952-1

RDELAY

tDELAY

SOUT

OUT

Programming Maximum Duty Cycle Clamp

For forward converter applications using the simplest

topology of a single MOSFET on the primary, a maximum

switch duty cycle clamp which adapts to transformer

input voltage is necessary for reliable control of the

MOSFET. This volt-second clamp provides a safeguard for

transformer reset that prevents transformer saturation. The

LT1952/LT1952-1 SD_VSEC and SS_MAXDC pins provide a

capacitor-less, programmable volt-second clamp solution

using simple resistor ratios (Figure 9).

An increase of voltage at the SD_VSEC pin causes the

maximum duty cycle clamp to decrease. Deriving SD_VSEC

from a resistor divider connected to system input voltage

creates the volt-second clamp. The maximum duty cycle

clamp can be adjusted by programming voltage on the

Figure 9. Programming Maximum Duty Cycle Clamp

SYSTEM

INPUT VOLTAGE

ADAPTIVE

DUTY CYCLE

CLAMP INPUT

MAX DUTY CYCLE

CLAMP ADJUST INPUT

*MINIMUM ALLOWABLE RT IS 10k TO

GUARANTEE SOFT-START PULL-OFF

1952 F09

SD_VSEC

SS_MAXDC

VREF

LT1952/

LT1952-1

RT*

LT1952IGN Datenblatt(PDF) 15 Page - Linear Technology

LT1952IGN Datenblatt(HTML) 15 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

Datenblatt Download

Link URL