LT1952IGN datasheet(17/24 Pages) LINER

17 / 24 page

LT1952/LT1952-1

19521fd

(A) VIN > 14.25* (7.75V LT1952-1), and

(B) SD_VSEC > 1.32V, and

(D) SS_MAXDC < 0.45V (SS_MAXDC reset threshold)

*VIN>8.75V(6.5VLT1952-1)isokforlatchresetifthelatch

was only set by overcurrent condition in (3) above.

SS_MAXDC Discharge Timing

It can be seen in Figure 10 that two types of discharge

can occur for the SS_MAXDC pin. In timing (A) the fault

that caused the soft-start event has been removed before

SS_MAXDC falls to 0.45V. This means the soft-start

latch will be reset when SS_MAXDC falls to 0.45V and

SS_MAXDC will begin charging. In timing (B), the fault that

caused the soft-start event is not removed until some time

after SS_MAXDC has fallen past 0.45V. The SS_MAXDC

pin continues to discharge to 0.2V and remains low until

all faults are removed.

The time for SS_MAXDC to fall to a given voltage can be

approximated as:

SS_MAXDC (tFALL) =

(CSS/IDIS) • [SS_MAXDC(DC) – VSS(MIN)]

where:

IDIS = net discharge current on CSS

CSS = capacitor value at SS_MAXDC pin

SS_MAXDC(DC) = programmed DC voltage

VSS(MIN) = minimum SS_MAXDC voltage before

recharge

IDIS ~ 8e–4 + (VREF – VSS(MIN))[(1/2RB) – (1/RT)]

For faults arising from (1) and (2),

VREF = 100mV.

For a fault arising from (3),

VREF = 2.5V.

SS_MAXDC(DC) = VREF[RB/(RT + RB)]

VSS(MIN) = SS_MAXDC reset threshold = 0.45V

(if fault removed before tFALL)

APPLICATIONS INFORMATION

Example:

For an overcurrent fault (OC > 100mV), VREF = 2.5V,

RT = 35.7k, RB = 100k, CSS = 0.1μF and assume

VSS(MIN) = 0.45V,

IDIS ~ 8e–4 + (2.5 – 0.45)[(1/2 • 100k) – (1/35.7k)]

= 8e–4 + (2.05)(–0.23e–4) = 7.5e–4

SS_MAXDC(DC) = 1.84V

SS_MAXDC (tFALL) = (1e – 7/7.5e–4) • (1.84 – 0.45)

= 1.85e–4 s

If the OC fault is not removed before 185μs then SS_MAXDC

will continue to fall past 0.45V towards a new VSS(MIN).

The typical VOL for SS_MAXDC at 150μA is 0.2V.

SS_MAXDC Charge Timing

When all faults are removed and the SS_MAXDC pin

has fallen to its reset threshold of 0.45V or lower, the

SS_MAXDC pin will be released and allowed to charge.

SS_MAXDC will rise until it settles at its programmed DC

voltage—setting the maximum switch duty cycle clamp.

The calculation of charging time for the SS_MAXDC pin

between any two voltage levels can be approximated as

an RC charging waveform using the model shown in

Figure 11.

The ability to predict SS_MAXDC rise time between any two

voltages allows prediction of several key timing periods:

(1)No Switching Period

(time from SS_MAXDC(DC) to VSS(MIN) + time from

VSS(MIN) to VSS(ACTIVE))

(2)Converter Output Rise Time

(time from VSS(ACTIVE) to VSS(REG); VSS(REG) is the

level of SS_MAXDC where maximum duty cycle

clamp equals the natural duty cycle of the switch)

(3)Time For Maximum Duty Cycle Clamp within X% of

Target Value

The time for SS_MAXDC to charge to a given voltage VSS

is found by re-arranging:

LT1952IGN Datenblatt(PDF) 17 Page - Linear Technology

LT1952IGN Datenblatt(HTML) 17 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

Datenblatt Download

Link URL