MCP3901 datasheet(23/60 Pages) MICROCHIP

23 / 60 page

DS22192C-page 23

MCP3901

4.16

Crosstalk

The crosstalk is defined as the perturbation caused by

one ADC channel on the other ADC channel. It is a

measurement of the isolation between the two ADCs

present in the chip.

This measurement is a two-step procedure:

Measure one ADC input with no perturbation on

the other ADC (ADC inputs shorted).

Measure

the

same

ADC

input

with

perturbation sine wave signal on the other ADC

at a certain predefined frequency.

The crosstalk is then the ratio between the output

power of the ADC when the perturbation is present and

when it is not divided by the power of the perturbation

signal.

A higher crosstalk value implies more independence

and isolation between the two channels.

The measurement of this signal is performed under the

following conditions:

•GAIN = 1,

• PRESCALE = 1,

• OSR = 256,

• MCLK = 4 MHz

Step 1

• CH0+ = CH0- = AGND

• CH1+ = CH1- = AGND

Step 2

• CH0+ = CH0- = AGND

• CH1+ – CH1- = 1 VP-P @ 50/60 Hz (full-scale

sine wave)

The crosstalk is then calculated with the following

formula:

EQUATION 4-10:

4.17

PSRR

This is the ratio between a change in the power supply

voltage and the ADC output codes. It measures the

influence of the power supply voltage on the ADC

outputs.

The PSRR specification can be DC (the power supply

is taking multiple DC values) or AC (the power supply

is a sinewave at a certain frequency with a certain

common-mode). In AC, the amplitude of the sinewave

is representing the change in the power supply.

It is defined as:

EQUATION 4-11:

Where VOUT is the equivalent input voltage that the

output code translates to with the ADC transfer

function. In the MCP3901 specification, AVDD varies

from 4.5V to 5.5V, and for AC PSRR, a 50/60 Hz

sinewave is chosen, centered around 5V with a

maximum 500 mV amplitude. The PSRR specification

is measured with AVDD = DVDD.

4.18

CMRR

This

the

ratio

between

change

the

common-mode input voltage and the ADC output

codes. It measures the influence of the common-mode

input voltage on the ADC outputs.

The

CMRR

specification

can

(the

common-mode input voltage is taking multiple DC

values) or AC (the common-mode input voltage is a

sinewave at a certain frequency with a certain

common-mode). In AC, the amplitude of the sinewave

is representing the change in the power supply.

It is defined as:

EQUATION 4-12:

Where VCM = (CHn+ + CHn-)/2 is the common-mode

input voltage and VOUT is the equivalent input voltage,

the output code is translated to the ADC transfer

function. In the MCP3901 specification, VCM varies

from -1V to +1V, and for the AC specification, a 50/

60 Hz sinewave is chosen, centered around 0V, with a

500 mV amplitude.

4.19

ADC Reset Mode

ADC Reset mode (also called Soft Reset mode) can

only be entered through setting the RESET<1:0> bits

high in the Configuration register. This mode is defined

as the condition where the converters are active, but

their output is forced to ‘0’.

The registers are not affected in this Reset mode and

retain their values.

The ADCs can immediately output meaningful codes

after leaving Reset mode (and after the sinc filter set-

tling time of 3/DRCLK). This mode is both entered and

exited through the setting of bits in the Configuration

CTalk dB

()

ΔCH0Power

ΔCH1Power

---------------------------------

⎝⎠

⎛⎞

log

PSRR dB

()

ΔV

OUT

ΔAV

-------------------

⎝⎠

⎛⎞

log

CMRR dB

()

ΔV

OUT

ΔV

-----------------

⎝⎠

⎛⎞

log

MCP3901 Datenblatt(PDF) 23 Page - Microchip Technology

MCP3901 Datenblatt(HTML) 23 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Datenblatt Download

Link URL