POE-D10-00-E-13

SAFETY STANDARDS REGULATED, REINFORCED

INSULATION TYPE, AH SERIES

Ver: 13

Page: 10 / 18

7. Specification and test method:

7.1 Operating Temperature Range: -40 to +125°C

7.2 Test condition:

Test and measurement shall be made at the standard condition. (temperature 15~35

, relative humidity 45~75%

℃

and atmospheric pressure 860~1060hpa). Unless otherwise specified herein.

If doubt occurred on the value of measurement, and measurement was requested by customer capacitors shall be

measured at the reference condition. (temperature 20±2

or25 ± 2

, relative humidity 60~70% and atmospheric

℃

℃

pressure 860~1060hpa.)

7.3 Performance:

No

Items

Performance

Testing method

7.3.1

Appearance

And dimension

The appearance and dimension

shall be as given in section 3.

Visual check.

7.3.2

Marking

The marking shall be easily

legible. (As given section 5)

Visual check.

Between

terminals

No failure.

The capacitors shall not be damage when AC4000V

(rms.) are applied between the lead wires for 60sec.

7.3.3

Withstand

voltage

Body

Insulation

No failure.

First. The terminals of the capacitor shall be closely

wrapped around the body of the capacitor distance of

about 3 to 4mm from each terminal. Then, the

capacitor shall be inserted into a container filled with

metal balls of about 1mm diameter. Finally, AC4000V

(rms.) is applied for 60sec between the capacitor lead

50mA.

)

7.3.4

Insulation

Resistance

Between

terminals

10000M

or more.

The insulation resistance shall be measured with

DC500±50V within 60±5sec of charging.

7.3.5

Capacitance

Within specified tolerance.

7.3.6

Dissipation

Factor(tanδ) or Q

Y5P、Y5U：D.F.

2.5%

≦

Y5V：D.F.

5.0%

≦

CH&SL：

30pF&above:

1000

≧

Below 30PF:

400+20×C

≧

Y5P&Y5U&Y5V: The capacitance shall be measured

at 20±2

with 1kHz±20% and 5V(rms.) or less.

℃

CH&SL: The capacitance shall be measured at 25℃

with 1MHz±20% and1.0±0.2Vrms

7.3.7

Temperature

Characteristic

The capacitance measurement shall be made at each

step specified in Table 1.

Pre-treatment:

Capacitor shall be stored at 85±2

for 1hour, then

℃

placed at

1

measurements.

7.3.8

Solderability of Leads

Lead wire should be

soldered

with

uniform

coating

on

the

axial

direction over

3/4

of the

circumferential direction.

The lead wire of capacitor should be dipped into

molten solder for 5 ± 0.5 sec.

The depth of immersion is up to about 1.5 to 2.0 mm

from the root of lead wires.

Temp. of solder：Lead Free Solder ( Sn-3Ag-0.5Cu)

245±5℃

Table 1

Step

Temperature (℃)

1

+20±2

2

-25±2

3

+20±2

4

+85±2

5

+20±2

Char. Capacitance Change

Y5P Within ± 10%

Y5U Within ±

２

５

０

Y5V Within –80 ~ +30%

CH

0

±60ppm/℃

SL

-1000~+350

ppm/

℃

(+20

~+85

℃

℃)