MCP3910 datasheet(19/90 Pages) MICROCHIP

19 / 90 page

 2012-2020 Microchip Technology Inc.

DS20005116D-page 19

MCP3910

3.0

PIN DESCRIPTION

The descriptions of the pins are listed in Table 3-1.

3.1

Master Reset/OSR0 Logic Input

(RESET/OSR0)

In SPI mode, this pin is active-low and places the entire

chip in a Reset state when active.

When RESET is logic low, all registers are reset to their

default value, no communication can take place, no

clock is distributed inside the part, except in the input

structure if MCLK is applied (if MCLK is Idle, then no

clock is distributed). This state is equivalent to a

Power-on Reset (POR) state.

Since the default state of the ADCs is on, the analog

power consumption when RESET is logic low is equiv-

alent to when RESET is logic high. Only the digital

power consumption is largely reduced because this

current consumption is essentially dynamic and is

reduced drastically when there is no clock running.

All the analog biases are enabled during a Reset, so

that the part is fully operational just after a RESET

rising edge, if MCLK is applied when RESET is logic

low. If MCLK is not applied, there is a time after a hard

Reset when the conversion may not accurately

correspond to the start-up of the input structure.

This input is Schmitt triggered.

In Two-Wire Interface mode, this is the OSR0 logic

select pin (see Section 7.0 “Two-Wire Serial Inter-

face Description”

for the logic input table for OSR0

and OSR1). The pin state is latched when the MODE

changes to Two-Wire Interface mode and is relatched

at each Watchdog Timer Reset.

TABLE 3-1:

TWO-CHANNEL MCP3910 PIN FUNCTION TABLE

MCP3910

SSOP

MCP3910

QFN

Symbol

Function

RESET/OSR0

Master Reset Logic Input Pin or OSR0 Logic Input Pin

219

DVDD

Digital Power Supply Pin

320

AVDD

Analog Power Supply Pin

CH0+

Noninverting Analog Input Pin for Channel 0

CH0-

Inverting Analog Input Pin for Channel 0

CH1-

Inverting Analog Input Pin for Channel 1

CH1+

Noninverting Analog Input Pin for Channel 1

AGND

Analog Ground Pin, Return Path for Internal Analog Circuitry

REFIN+/OUT

Noninverting Voltage Reference Input and Internal Reference

Output Pin

REFIN-

Inverting Voltage Reference Input Pin

DGND

Digital Ground Pin, Return Path for Internal Digital Circuitry

MDAT1

Modulator Data Output Pin for Channel 1

MDAT0

Modulator Data Output Pin for Channel 0

DR/GAIN1

Data Ready Signal Output Pin or GAIN1 Logic Input Pin

OSC1/CLKI/GAIN0 Oscillator Crystal Connection Pin or External Clock Input Pin or

GAIN0 Logic Input Pin

OSC2/MODE

Oscillator Crystal Connection Pin or Serial Interface Mode Logic

Input Pin

CS/BOOST

Serial Interface Chip Select Input Pin or Boost Logic Input Pin

SCK/MCLK

Serial Interface Clock Input Pin or Master Clock Input Pin

SDO

Serial Interface Data Input Pin

SDI/OSR1

Serial Interface Data Input Pin or OSR1 Logic Input Pin

—

Exposed Thermal Pad.

MCP3910 Datenblatt(PDF) 19 Page - Microchip Technology

MCP3910 Datenblatt(HTML) 19 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90

Datenblatt Download

Link URL