ATmega16 datasheet(70/357 Pages) ATMEL

70 / 357 page

2466S–AVR–05/09

ATmega16(L)

and/or falling edge of the INT1 pin or level sensed. Activity on the pin will cause an interrupt

request even if INT1 is configured as an output. The corresponding interrupt of External Interrupt

Request 1 is executed from the INT1 interrupt Vector.

• Bit 6 – INT0: External Interrupt Request 0 Enable

When the INT0 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), the exter-

nal pin interrupt is enabled. The Interrupt Sense Control0 bits 1/0 (ISC01 and ISC00) in the MCU

General Control Register (MCUCR) define whether the External Interrupt is activated on rising

and/or falling edge of the INT0 pin or level sensed. Activity on the pin will cause an interrupt

request even if INT0 is configured as an output. The corresponding interrupt of External Interrupt

Request 0 is executed from the INT0 interrupt vector.

• Bit 5 – INT2: External Interrupt Request 2 Enable

When the INT2 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), the exter-

nal pin interrupt is enabled. The Interrupt Sense Control2 bit (ISC2) in the MCU Control and

Status Register (MCUCSR) defines whether the External Interrupt is activated on rising or falling

edge of the INT2 pin. Activity on the pin will cause an interrupt request even if INT2 is configured

as an output. The corresponding interrupt of External Interrupt Request 2 is executed from the

INT2 Interrupt Vector.

General Interrupt Flag

• Bit 7 – INTF1: External Interrupt Flag 1

When an edge or logic change on the INT1 pin triggers an interrupt request, INTF1 becomes set

(one). If the I-bit in SREG and the INT1 bit in GICR are set (one), the MCU will jump to the corre-

sponding Interrupt Vector. The flag is cleared when the interrupt routine is executed.

Alternatively, the flag can be cleared by writing a logical one to it. This flag is always cleared

when INT1 is configured as a level interrupt.

• Bit 6 – INTF0: External Interrupt Flag 0

When an edge or logic change on the INT0 pin triggers an interrupt request, INTF0 becomes set

(one). If the I-bit in SREG and the INT0 bit in GICR are set (one), the MCU will jump to the corre-

sponding interrupt vector. The flag is cleared when the interrupt routine is executed.

Alternatively, the flag can be cleared by writing a logical one to it. This flag is always cleared

when INT0 is configured as a level interrupt.

• Bit 5 – INTF2: External Interrupt Flag 2

When an event on the INT2 pin triggers an interrupt request, INTF2 becomes set (one). If the I-

bit in SREG and the INT2 bit in GICR are set (one), the MCU will jump to the corresponding

Interrupt Vector. The flag is cleared when the interrupt routine is executed. Alternatively, the flag

can be cleared by writing a logical one to it. Note that when entering some sleep modes with the

INT2 interrupt disabled, the input buffer on this pin will be disabled. This may cause a logic

change in internal signals which will set the INTF2 Flag. See “Digital Input Enable and Sleep

Modes” on page 54 for more information.

Bit

654

INTF1

INTF0

INTF2

–

–GIFR

Read/Write

R/W

Initial Value

ATmega16 Datenblatt(PDF) 70 Page - ATMEL Corporation

ATmega16 Datenblatt(HTML) 70 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datenblatt Download

Link URL