TMS320VC5421 datasheet(13/88 Pages) TI

13 / 88 page

TMS320VC5421

DIGITAL SIGNAL PROCESSOR

SPRS098 – DECEMBER 1999

POST OFFICE BOX 1443

• HOUSTON, TEXAS 77251–1443

Signal Descriptions (Continued)

NAME

DESCRIPTION

TYPE†

HOST-PORT INTERFACE (HPI) SIGNALS (CONTINUED)

PRIMARY

HD[15:0]

I/O/Z

PPD[15:0]

I/O/Z

Parallel bidirectional data bus. These pins are multiplexed with the external

interface pins and are used as an HPI interface when XIO = 0.

The data bus includes bus holders to reduce power dissipation caused by

floating, unused pins. The bus holders also eliminate the need for external pullup

resistors on unused pins. When the data bus is not being driven by the ’5421, the

bus holders keep address pins at the last driven logic level. The data bus keepers

are disabled at reset and can be enabled/disabled via the BH bit of the BSCR

See the PPD signal descriptions. These pins are placed into the high-impedance

state when OFF is low.

HCNTL0

HCNTL1

PPA3

PPA2

O/Z

HPI control inputs. Use PPA3 and PPA2 for the HCNTL0 and HCNTL1 values

during the HPI HPIC, HPIA, and HPID reads/writes. Only used in multiplexed

address/data mode (HMODE = 0).

These pins are shared with the external memory interface and are only used by

the HPI when the interface is in HPI mode (XIO pin is low). These pins are placed

into the high-impedance state when OFF is low.

HAS‡§

PPA4‡§

O/Z

Address strobe input. Hosts with multiplexed address and data pins require HAS

to latch the address in the HPIA register. This signal is only used in HPI

multiplexed address/data mode (HMODE pin is low).

This pin is shared with the external memory interface and is only used by the HPI

when the interface is in HPI mode (XIO pin is low). This pin is placed into the

high-impedance state when OFF is low.

HCS‡§

MSTRB‡§

O/Z

HPI chip-select signal. This signal must be active during HPI transfers, and can

remain active between concurrent transfers.

This pin is shared with the external memory interface and is only used by the HPI

when the interface is in HPI mode (XIO pin is low). This pin is placed into the

high-impedance state when OFF is low.

HDS1‡§

HDS2‡§

PS‡§

DS‡§

O/Z

HPI data strobes. HDS1 and HDS2 are driven by the host read and write strobes

to control HPI transfers.

These pins are shared with the external memory interface and are only used by

the HPI when the interface is in HPI mode (XIO pin is low).

These pins are placed into the high-impedance state when OFF is low.

HR/W

R/W

O/Z

HPI read/write signal. This signal is used by the host to control the direction of an

HPI transfer.

This pin is shared with the external memory interface and is only used by the HPI

when the interface is in HPI mode (XIO pin is low).

This pin is placed into the high-impedance state when OFF is low.

HRDY

O/Z

READY

HPI data-ready output. The ready output informs the host when the HPI is ready

for the next transfer.

This pin is shared with the external memory interface and is only used by the HPI

when the interface is in HPI mode (XIO pin is low). HRDY is placed into the

high-impedance state when OFF is low.

† I = Input, O = Output, S = Supply, Z = High Impedance

‡ This pin has an internal pullup resistor.

§ These pins are Schmitt triggered inputs.

¶ This pin has an internal bus holder controlled by way of the BSCR register in 54x cLEAD core of DSP subsystem A .

# This pin is used by Texas Instruments for device testing and should be left unconnected.

|| This pin has an internal pulldown resistor.

TMS320VC5421 Datenblatt(PDF) 13 Page - Texas Instruments

TMS320VC5421 Datenblatt(HTML) 13 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88

Datenblatt Download

Link URL