STM32U595AI datasheet(68/377 Pages) STMICROELECTRONICS

68 / 377 page

Functional overview

STM32U59xxx

68/377

DS13633 Rev 1

3.31.4

Internal voltage reference (VREFINT)

The VREFINT provides a stable (bandgap) voltage output for the ADC and the comparators.

The VREFINT is internally connected to ADC1, ADC2 and ADC4 input channels.

The precise voltage of VREFINT is individually measured for each part by

STMicroelectronics during production test and stored in the system memory area. It is

accessible in read-only mode.

3.31.5

VBAT battery voltage monitoring

This embedded hardware enables the application to measure the VBAT battery voltage using

ADC1, ADC2 or ADC4 input channel. As the VBAT voltage may be higher than the VDDA,

and thus outside the ADC input range, the VBAT pin is internally connected to a bridge

divider by four. As a consequence, the converted digital value is a quarter of the VBAT

voltage.

3.32

Digital to analog converter (DAC)

The DAC module is a 12-bit, voltage output digital-to-analog converter. The DAC can be

configured in 8- or 12-bit mode and may be used in conjunction with the DMA controller.

In 12-bit mode, the data may be left- or right-aligned.

The DAC features two output channels, each with its own converter. In dual DAC channel

mode, conversions can be done independently or simultaneously when both channels are

grouped together for synchronous update operations. An input reference pin, VREF+

(shared with others analog peripherals) is available for better resolution. An internal

reference can also be set on the same input.

The DAC_OUTx pin can be used as general purpose input/output (GPIO) when the DAC

output is disconnected from output pad and connected to on chip peripheral. The DAC

output buffer can be optionally enabled to allow a high drive output current. An individual

calibration can be applied on each DAC output channel. The DAC output channels support

a low-power mode, the sample and hold mode.

The digital interface supports the following features:

•

One DAC interface, maximum two output channels

Table 16. Temperature sensor calibration values

Calibration

value name

Description

Memory address

TS_CAL1

Temperature sensor 14-bit raw data acquired by ADC1

at 30 °C (± 5 °C), VDDA = VREF+ = 3.0 V (± 10 mV)

0x0BFA 0710 - 0x0BFA 0711

TS_CAL2

Temperature sensor 14-bit raw data acquired by ADC1

at 130 °C (± 5 °C), VDDA = VREF+ = 3.0 V (± 10 mV)

0x0BFA 0742 - 0x0BFA 0743

Table 17. Internal voltage reference calibration values

Calibration value name

Description

Memory address

VREFINT_CAL

14-bit raw data acquired by ADC1

at 30 °C (± 5 °C), VDDA = VREF+ = 3.0 V (± 10 mV)

0x0BFA 07A5 - 0x0BFA 07A6

STM32U595AI Datenblatt(PDF) 68 Page - STMicroelectronics

STM32U595AI Datenblatt(HTML) 68 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datenblatt Download

Link URL