 |
Datenblatt-Suchmaschine für elektronische Bauteile |
|
|
Datenblatt-Suchmaschine für elektronische Bauteile |
|
AM79C976 Datenblatt(PDF) 42 Page - Advanced Micro Devices |
|
|
|||||||||||||||||||||||||||||
AM79C976 Datenblatt(HTML) 42 Page - Advanced Micro Devices |
|
|
42 / 309 page  42 Am79C976 8/01/00 P R E L I M INARY )LJXUH1RQ%XUVW 5HDG7UDQVIHU The FIFO thresholds should be greater than or equal to the cache line size to maximize the use of the MRL and MRM commands. If the PCI bridge stops a transfer, the Am79C976 device waits until the FIFO threshold con- ditions are met before resuming the transfer. During the address phase of a burst access, AD[1:0] will both be 0 indicating a linear burst order. Note that during a burst read operation, all byte lanes will always be active. The Am79C976 controller will internally dis- card unneeded bytes. The Am79C976 controller will always perform only a single burst read transaction per bus mastership pe- riod, where transaction is defined as one address ph as e and o ne or mul t i p l e dat a p h a s es. T h e Am79C976 controller supports zero wait state read cy- cles. It asserts IRDY immediately after the address phase and at the same time starts sampling DEVSEL. FRAME is deasserted when the next-to-last data phase is completed. The device may insert IRDY wait states in the middle of a burst read transaction. Figure 12 shows a typical burst read access. The Am79C976 controller arbitrates for the bus, is granted access, reads three 32-bit words (DWord) from the sys- tem memory, and then releases the bus. In the exam- ple, the memory system extends the data phase of each access by one wait state. %DVLF1RQ%XUVW :ULWH7UDQVIHU The Am79C976 controller uses non-burst cycles to write descriptors when SWSTYLE (BCR20, bits 7-0) is 0 or 2. All Am79C976 controller non-burst write ac- cesses are of the PCI command type Memory Write (type 7). The byte enable signals indicate the byte lanes that have valid data.The Am79C976 controller may perform more than one non-burst write transaction within a single bus mastership period. FRAME is dropped between consecutive non-burst write cycles. REQ, however, stays asserted until FRAME is asserted for the last transaction. The Am79C976 supports zero wait state write cycles. (See the section Descriptor DMA Transfers for the only exception.) It asserts IRDY immediately after the address phase. Figure 13 shows two non-burst write transactions. The first transaction has two wait states. The Am79C976 device supports zero wait state non-burst write cycles. FRAME CLK AD IRDY TRDY C/BE DEVSEL REQ GNT PAR DEVSEL is sampled ADDR 0110 PAR 1 2345678 10 9 11 DATA ADDR DATA PAR PAR PAR 0000 0110 0000 22929B13 |
|
Link URL |
| War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Link zum Datenblatt | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
German ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
