MPC5644BCAMMJ1 datasheet(55/116 Pages) NXP

55 / 116 page

Electrical Characteristics

MPC5646C Microcontroller DataSheet, Rev. 7

NXP Semiconductors

The internal voltage regulator requires external bulk capacitance (CREGn) to be connected to the device to provide a stable low

voltage digital supply to the device. Also required for stability is the CDEC2 capacitor at ballast collector. This is needed to

minimize sharp injection current when ballast is turning ON. Apart from the bulk capacitance, user should connect

EMI/decoupling cap (CREGP) at each VDD_LV/VSS_LV pin pair.

4.8.1.1

Recommendations

•

The external NPN driver must be BCP68 type.

•VDD_LV should be implemented as a power plane from the emitter of the ballast transistor.

•10

μF capacitors should be connected to the 4 pins closest to the outside of the package and should be evenly

distributed around the package. For BGA packages, the balls should be used are D8, H14, R9, J3–one cap on each side

of package.

— There should be a track direct from the capacitor to this pin (pin also connects to VDD_LV plane). The tracks ESR

should be less than 100 m

Ω.

— The remaining VDD_LV pins (exact number will vary with package) should be decoupled with 0.1 μF caps,

connected to the pin as per 10

μF.

(see Section 4.4, “Recommended operating conditions”).

4.8.2

VDD_BV options

•

Option 1: VDD_BV shared with VDD_HV_A

VDD_BV must be star routed from VDD_HV_A from the common source. This is to eliminate ballast noise injection on

the MCU.

•

Option 2: VDD_BV independent of the MCU supply

VDD_BV > 2.6 V for correct functionality. The device is not monitoring this supply hence the external component must

meet the 2.6 V criteria through external monitoring if required.

Table 22. Voltage regulator electrical characteristics

Symbol

Parameter

Conditions1

Value2

Unit

Min

Typ

Max

CREGn

SR — External ballast stability capacitance

—

μF

RREG

SR — Stability capacitor equivalent serial

resistance

——

—

0.2

CREGP

SR — Decoupling capacitance (Close to

the pin)

VDD_HV_A/HV_B/VSS_HV

pair

100

—

VDD_LV/VSS_LV pair

100

—

CDEC2

SR — Stability capacitance regulator

supply (Close to the ballast collector)

VDD_BV/VSS_HV

—

μF

VMREG

CC P Main regulator output voltage

Before trimming

—

1.32

—

After trimming

TA = 25 °C

1.20

1.28

—

IMREG

SR — Main regulator current provided to

VDD_LV domain

——

—

350

IMREGINT

CC D Main regulator module current

consumption

IMREG = 200 mA

—

IMREG = 0 mA

—

MPC5644BCAMMJ1 Datenblatt(PDF) 55 Page - NXP Semiconductors

MPC5644BCAMMJ1 Datenblatt(HTML) 55 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datenblatt Download

Link URL