ATtiny45 datasheet(42/196 Pages) ATMEL

42 / 196 page

7598H–AVR–07/09

ATtiny25/45/85

8.9.1

Watchdog Timer Control Register – WDTCR

• Bit 7 – WDIF: Watchdog Timeout Interrupt Flag

This bit is set when a time-out occurs in the Watchdog Timer and the Watchdog Timer is config-

ured for interrupt. WDIF is cleared by hardware when executing the corresponding interrupt

handling vector. Alternatively, WDIF is cleared by writing a logic one to the flag. When the I-bit in

SREG and WDIE are set, the Watchdog Time-out Interrupt is executed.

• Bit 6 – WDIE: Watchdog Timeout Interrupt Enable

When this bit is written to one, WDE is cleared, and the I-bit in the Status Register is set, the

Watchdog Time-out Interrupt is enabled. In this mode the corresponding interrupt is executed

instead of a reset if a timeout in the Watchdog Timer occurs.

If WDE is set, WDIE is automatically cleared by hardware when a time-out occurs. This is useful

for keeping the Watchdog Reset security while using the interrupt. After the WDIE bit is cleared,

the next time-out will generate a reset. To avoid the Watchdog Reset, WDIE must be set after

each interrupt.

• Bit 4 – WDCE: Watchdog Change Enable

This bit must be set when the WDE bit is written to logic zero. Otherwise, the Watchdog will not

be disabled. Once written to one, hardware will clear this bit after four clock cycles. Refer to the

description of the WDE bit for a Watchdog disable procedure. This bit must also be set when

changing the prescaler bits. See “Timed Sequences for Changing the Configuration of the

Watchdog Timer” on page 44.

• Bit 3 – WDE: Watchdog Enable

When the WDE is written to logic one, the Watchdog Timer is enabled, and if the WDE is written

to logic zero, the Watchdog Timer function is disabled. WDE can only be cleared if the WDCE bit

has logic level one. To disable an enabled Watchdog Timer, the following procedure must be

followed:

In the same operation, write a logic one to WDCE and WDE. A logic one must be writ-

ten to WDE even though it is set to one before the disable operation starts.

Within the next four clock cycles, write a logic 0 to WDE. This disables the Watchdog.

In safety level 2, it is not possible to disable the Watchdog Timer, even with the algorithm

described above. See “Timed Sequences for Changing the Configuration of the Watchdog

Timer” on page 44.

Bit

765

432

WDIF

WDIE

WDP3

WDCE

WDE

WDP2

WDP1

WDP0

WDTCR

Read/Write

R/W

Initial Value

Table 8-6.

Watchdog Timer Configuration

WDE

WDIE

Watchdog Timer State

Action on Time-out

Stopped

None

Running

Interrupt

Running

Reset

Running

Interrupt

ATtiny45 Datenblatt(PDF) 42 Page - ATMEL Corporation

ATtiny45 Datenblatt(HTML) 42 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datenblatt Download

Link URL