SPSB100 datasheet(34/213 Pages) STMICROELECTRONICS

34 / 213 page

•

A fault on one of the regulators occurred and its REGFAIL_GO_REC configuration bit is set to 1.

•

FBB pin voltage falls below its power down threshold.

SPSB100 enters in RECOVERY-2 state from ACTIVE state and generates status register bit

REC2_FROM_DO_POWER_CYCLE = 01 in case of DO_POWER_CYCLE SPI command (only after

SPI_PROTECT_ACCESS has been set) REC2_FROM_DO_POWER_CYCLE can be cleared by

CLR_REC2_FROM_DO_POWER_CYCLE bit.

SPSB100 enters in RECOVERY-2 state from RECOVERY-1 state and generates status register bit

FSM_TO_REC2 = 1 in case of:

•

DO_POWER_CYCLE SPI command (only after SPI_PROTECT_ACCESS has been set).

•

The temperature of the central sensor overpassed the TSDC threshold.

•

A fault on one of the regulators occurred and its REGFAIL_GO_REC configuration bit is set to 1.

•

8 consecutive WD trigger faults.

•

FBB pin voltage falls below its power down threshold.

SPSB100 enters in RECOVERY-2 state from RECOVERY-1 state and generates status register bit

REC2_FROM_DO_POWER_CYCLE = 1X in case of DO_POWER_CYCLE SPI command (only after

SPI_PROTECT_ACCESS has been set) REC2_FROM_DO_POWER_CYCLE can be cleared by

CLR_REC2_FROM_DO_POWER_CYCLE bit.

When entering RECOVERY-2 state:

•

The NFSO1 output is asserted low.

•

FCCU monitoring is turned OFF.

•

NRST is asserted low and regulators are turned off according to the programmed power-down sequence.

•

In case of a TSD event the TSD counter is incremented and SPSB100 waits that the temperature cools

down.

From RECOVERY-2 state SPSB100 transits to DEEP-SLEEP state for unrecoverable fault, or to INIT state to

power-up again.

3.6.3.8

DEEP-SLEEP state - Unrecoverable faults

SPSB100 enters in DEEP-SLEEP state from ACTIVE-FULL-POWER mode or REC-1 states in case of:

•

DO_POWER_DOWN SPI command (only after SPI_PROTECT_ACCESS has been set).

•

Power ground lost.

SPSB100 enters in DEEP-SLEEP state from RECOVERY-1 state in case of:

•

DO_POWER_DOWN SPI command (only after SPI_PROTECT_ACCESS has been set).

•

Power ground lost.

•

15 consecutive WD trigger faults.

SPSB100 enters in DEEP-SLEEP state from RECOVERY-2 state in case of:

•

The temperature of one sensor overpassed the TSD threshold and the TSD counter (TSD_CNT_FAIL)

reached 3.

•

The counter of regulator (REG_FAIL_CNT) fail events reached 3.

When entering the DEEP-SLEEP state from ACTIVE or RECOVERY-1 states:

•

The NFSO1 output is asserted low.

•

FCCU monitoring is turned OFF.

•

NRST is asserted low and regulators are turned off according to the programmed power-down sequence.

SPSB100 remains in a DEEP-SLEEP state until a wake-up event occurs. The design of SPSB100 has been

optimized to offer a very-low power consumption while being wake-able by external events.

DEEP-SLEEP state is also entered:

•

In case of hardware low-level error, refer to the Section 4.8: HW low-level monitors for details.

•

From INIT state in case of safety check error, refer to the Section 4.17: Safety checks for details.

•

In case of repetitive power-up fault, refer to the Section 3.6.2.3: Power-up fault management.

SPSB100

Functional description

DS14640 - Rev 2

page 34/213

SPSB100 Datenblatt(PDF) 34 Page - STMicroelectronics

SPSB100 Datenblatt(HTML) 34 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datenblatt Download

Link URL